15KV Boost High Voltage Generator High Frequency Transformer Inverter Arc Ign...

Description: 15KV Boost High Voltage Generator High Frequency Transformer Inverter Arc Igniter Coil Module Disassembled Parts for DIY Use 2Sets(Include PCB Board) This kit is made for the booster coil and has a professional circuit diagram for the convenience of electronics enthusiasts.1 set of list：PCB Board/120 ohm resistance/UF4007 ultra-fast recovery diode/N20 transistor/Heat sink/M3 * 6 screws/Boat switch/Pin header (3-8 Pin random) Uses: Chinese-language general experiments, electronic instruments, negative ion generators, scientific small production, etc. This circuit works with a stable high-frequency arc, which is extremely high in temperature and can easily ignite combustibles. Therefore, it is called a plasma lighter. Transformer structure: The transformer has two windings in the primary, one set of thick copper wire is the main winding, one set of thin copper wire is the feedback winding, and the secondary output is high voltage. In the transformer, two thick and thin copper wires are wound together, which are the main winding tail and the feedback winding head, respectively, connected to the positive pole of the power supply. Before welding the transformer, it is necessary to scrape off the welded portion of the coating and the covered wire tip with a blade and then solder. After successful production, the transformer must be potted with epoxy or insulating wax for long-term use. The maximum output of the transformer is designed to be 15KV, and the maximum output must not exceed 15KV, which is 1.5cm arc. The kit has an input voltage of 3.7V. That is, the voltage of the 18650 battery, if you need to increase the input voltage (maximum increase to 12V), you need to increase the resistance of the feedback resistor (package resistance is 120 ohms), otherwise the triode is easy to burn out. The feedback resistance is increased to approximately 150 Ω to 1.5 K Ω. Resistance should be adjusted from large to small. It should not be too small. Installation Notes: With the PCB board parts better production, in which the transformer line of thick line and thin line, this should pay attention to the other components by the board of silk symbols and parameters of welding on the line. Transformer board has done three pads, in which the middle of the pad hole is relatively large, the hole at the same time welding a thick enameled wire and a thin enameled wire, thick enameled wire and fine enameled wire do not use the same side, such as with the left Thick lines and the right side of the thin wire into or with the left side of the thin line and the right side of the thick line welding into, in short, do not use the same side of the thick lines and thin lines can be. In order to prevent the output 2-wire distance too far, resulting in no-load, you can weld a 3P pin at the output. After the success of the production, if the output access to a high-voltage capacitor and three high-voltage rectifier composed of voltage doubler circuit, you can produce DC high voltage, you can make anion generator, wiring diagram is as follows. Tips: If you are concerned about the quality of the components, please test them one by one before soldering. Once the solder is soldered, it is impossible to judge whether it is soldered or the component itself is bad. Please understand that! Shipping We offer FREE shipping on all orders! We ship within Three business days of payment, usually sooner. We use a selection of shipping services such as UPS, FedEx, USPS etc. We only ship to the lower 48 states, no APO/FPO addresses or PO Boxes allowed. Local pickups and combined shipping options are not provided at this time. Return You can return a product for up to 30 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. Payment We accept payment by any of the following methods:PayPalPlease pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! Feedback Customer satisfaction is very important to us. If you have any problem with your order, please contact us and we will do our best to make you satisfied. Contact Us If you have any queries, please contact us via ebay. We usually respond within 24 hours on weekdays. Please visit our eBay store to check out other items for sale! Thank you for shopping at our store.

Price: 9.59 USD

Location: Phoenix, AZ

End Time: 2024-12-01T16:02:47.000Z

Shipping Cost: 0 USD